신고사유
신고해주신 내용은 쇼핑몰 운영자의 검토 후 내부 운영 정책에 의해 처리가 진행됩니다.
루엣 - 데이비드3 플로어 룸
David III는 겸손해 보이지만 기능적인 면에서 많은 대형 바닥 직기를 능가하는 소형 8 하네스 직기입니다. 70cm (27 5/8 ") 및 90cm (35 3/8") 및 110cm (43 1/2 ") 직조 폭으로 제공됩니다.
새로운 데이비드 3는
1. 프레임이 더 튼튼합니다. 전면 포스트, 메인 업라이트 및 풋 레일의 두께는 27mm (기존 21mm)입니다.
2. 힌지 포인트가 바닥에 가까워 서있는 비터는 부드러운 움직임과 낙하 선을 치기위한 유리한 피벗 반경이됩니다.
3. 비터의 힌지 후크는 비터 수직이 아닌 베틀에 장착됩니다. 이렇게하면 비터를 쉽게 제거하고 교체 할 수 있습니다.
4. 워프 빔과 천 빔의 직경이 더 큽니다. 이것은 워프 빔을 감는 데 더 적은 회전이 필요하므로 워프 스레드의 장력 불일치가 적습니다. 단면 워프 키트에는 이제 3 대신 워프 빔에 부착되는 4 개의 바를위한 공간이 있습니다. 이렇게하면 조립 및 기능이 향상됩니다.
5. 새로운 천 빔 진행 레버를 추가했습니다. 래칫 휠에 폴을 고정하는 자석이있어 핸들을 한 번만 움직여 더 많은 천을 전진 할 수 있습니다.
6. 유방 빔에는 앞 기둥에 빔을 쉽게 장착 할 수 있도록 카운터 성크 구멍이 있습니다.
7. 발판 용 타이 업 코드는 램에 영구적으로 연결되어 있으며 필요한 곳에서 발판 위로 이동할 수 있습니다. 트레들에있는 나사 머리는 약간 작아서 코드에 쉽게 걸 수 있습니다.
8. 경사 빔의 장력 브레이크는 더 이상 액세서리가 아니라 표준입니다. 브레이크 디스크는 훨씬 더 크고 이제 워프를 감을 수있는 크랭크 핸들이기도합니다. 핸들은 손이 아닌 디스크에서 회전합니다.
9. 이제 널링 너트로 샤프트 높이를 조정하고 나사로 수평 조정을 할 수 있습니다. 따라서 코드의 작은 texsolv 핀이 더 이상 필요하지 않습니다.
10. David를 접는 것이 더 쉽고 잃어 버릴 수 있는 느슨한 부분이 없습니다.
11. 래들 위로 미끄러질 수 있는 나무 래들 커버가 포함되어 있습니다. 이것은 날실을 래들에 삽입 한 다음 날실을 감을 때 래들을 닫는 데 유용합니다.
12. 두 개의 측면 클램프가 포함되어있어 날실을 설치하고 나사를 조일 때 유용합니다.
13. 조립 설명서 외에 베틀을 입히는 방법에 대한 지침이 있습니다.
포함내용
스테인리스 스틸 리드 40-10 (미터법)
800 Texsolv 헤들 (280mm)
제휴 및 임대 스틱
16 개의 워프 스틱.
크기
D70 - 36 1/4 x 33 1/2” x 50”
D90 - 44” x 33 1/2” x 50”
D110 - 52” x 33 1/2” x 50"
Louet - David 3 Floor Loom
David 3 David III is a compact eight harness loom that looks modest, but in functional quality, it surpasses many large floor looms. It is available in 70 cm (27 5/8") and 90 cm (35 3/8") and 110cm (43 1/2”) weaving width.
Improvements of the David II
1. It has a sturdier frame: the front posts, the main uprights and the foot rail are 27 mm thick (was 21 mm).
2. Standing beater, with a hinge point close to the floor, the result is smooth movement and a favorable pivot radius to strike the fell line.
3. The hinge hooks of the beater are mounted on the loom and not on the beater uprights. This makes it easier to remove and replace the beater.
4. The warp beam and the cloth beam have a larger diameter. This requires fewer revolutions to wind your warp beam and therefore less tension discrepancies in the warp threads. The sectional warp kit now has space for 4 bars that attach to the warp beam, instead of 3. This improves assembly and function.
5. We have added a new cloth beam advance lever. It has a magnet that holds the pawl in the ratchet wheel, allowing you to advance more fabric with one movement of the handle.
6. The breast beam has countersunk holes to make it easier to mount the beam on the front posts.
7. The tie-up cords for the treadles are permanently connected to the lams and can be moved above the treadles where you need them. The screw heads on the treadles are slightly smaller, making it easier to hook on the cords.
8. The tension brake on the warp beam is no longer an accessory, but standard. The brake disc is much larger and is now also a crank handle with which you can wind on your warp. The handle rotates in the disc, not in your hand.
9. You can now adjust the shaft height with a knurled nut and the horizontal adjustment with a screw. Therefore the small texsolv pins in the cords are no longer needed.
10. Folding the David is easier and there are no loose parts that can get lost.
11. We include two wooden raddle covers that you can slide over the raddle. These are useful for inserting the warp threads into the raddle and then they close the raddle when winding on your warp.
12. Two side clamps are included and useful when setting up and threading the warp.
13. In addition to the assembly instructions, there are instructions on how to dress the loom.
a stainless steel reed 40-10 (metric)
800 Texsolv heddles (280 mm)
tie-up and lease sticks
sixteen warp sticks.
Dimensions: (W x D x H)
D70 - 36 1/4 x 33 1/2” x 50”
D90 - 44” x 33 1/2” x 50”
D110 - 52” x 33 1/2” x 50”
Accessories Available for purchase separately
Bench - height 57 cm (22 3/8")
Second warp beam with back beam
Sectional warp beam
Flying Dutchman shuttle
게시물이 없습니다
게시물이 없습니다